cokoino

Introduction to productsMore introduction Raspberry Pi Camera Module with Fixed Focus Lens for Modle A/B/B+,Pi 2B Pi 3B/B+ and Pi 4B The Camera Module Specifications is 2592 x 1944 Pixel Static Images, 1080 p @ 30 fps, 720 p @ 60 fps and 640 x480 p 60/90 Video Recording,5 Megapixel sensor OV5647 It has CSI Interface carries pixel data from the camera back to the processor, BY THE WAY with pi zero ribbon cable can be used on zero board Exterior size is L 25mm x W 24mm x H 7.5mm（L 0.98inch x W 0.94inch x H 0.3inch ) You will get it 1pcs Camera Module and 1pcs 15cm（5.9inch) FFC Cable Features:Angle of View: 54 x 41 degreesField of View: 2.0 x 1.33 m at 2 mFull-frame SLR lens equivalent: 35 mmFixed Focus: 1 m to infinityMax frame rate: 30fps15 cm flat ribbon cable to 15-pin MIPI Camera Serial Interface…

Introduction to productsMore introduction Overview The COKOINO ultrasonic module is compatible with the Arduino platform. It is mainly used for measuring distance and obstacle avoidance. It has the characteristics of high precision, super near blind zone (2cm) and stable performance. The module comes with 4 positioning holes for easy attachment to other devices. It can combine an arduino motherboard with other sensor and actuator modules to DIY into a variety of interesting products such as ultrasonic trolleys and ultrasonic robots. Specification (1) Typical working voltage: 5V(2) Ultra-small static working current: less than 5mA(3) Induction angle: no more than 15 degrees(4) Detection distance: 2cm-350cm(5) High precision: up to 0.2cm(6) Ultrasonic center frequency: 40KHz(7) Blind area (2cm) is very close(8)XH2.54-4P

Introduction to productsMore introduction (1) Working voltage: recommended working voltage 3-5V(2) Single LED specifications:Brightness: 18000-20000MCD brightnessVoltage: 2.9-3.1VPower: 0.06WCurrent: 20MAWavelength: 520-525(3) Input signal: digital signal(4) Interface: XH2.54-4P GND: Connect the negative pole of the power supplyVCC: Connect the positive pole of the power supply L1: Input high level, L1 LED lights up, input low level it goes outL2: input high level, L2 LED lights up, input low level it goes out

Introduction to products Specification Compatible with: arduino Maximum voltage input range: DC6.5—15V Recommended voltage input range: DC7—12V Maximum output current: 6.5V ≤ VIN ≤ 10V/5A Pin header specification: 2.54mm pitch Connector Specifications: XH2.54mm 4P Infrared receiving specification: IRM-3638T f=38KHz λ=940nm d=5.5m Serial port mother: 2.54mm pitch, can be directly inserted into hc-06 Bluetooth 2、Onboard buzzer specificationsModel: MLT-8530 (voltage type)Operating voltage: 4-6.5V (rated: 5V)Current: 90MA (max)Sound (10CM): 86dBFrequency: 2700Hz (31+/-3R)Operating ambient temperature: -20 to +60 degrees Celsius

Introduction to products Specifications (1) Typical working voltage: 5V (2) Working current: less than 20mA

Introduction to productsMore introduction Characteristic: 1. Compatible with LEGO building blocks mounting holes 2. convenient for external sensors to do experiments 3. High load capacity, integrated 3.3V/3A power supply Pico external sensor must be selected Perfect appearance design

Introduction to productsMore introduction This is a raspberry pi gpio extender kit that provides a way to easily connect your Raspberry Pi 4B/3B+/3B/ 2B/ 1B+ to a breadboard The rainbow ribbon, jumper wires and T connector board are really handy for getting the GPIO header to a breadboard for your creations 830 MB-102 Tie Points Solderless Breadboard is good quality and a nice size for quick prototyping. Great for testing circuits before committing them to a more permanent board and planning out a bigger project. Raspberry PI development board is not included in the kit Packing included:1 x 40 Pin Black T GPIO Extension Board1 x 20cm 40 Pin Rainbow Ribbon Cable1 x 830 breadboard65 x Jumper Cables NOTE: Raspberry Pi development board is not included.